inkright.blogg.se

1. Best way to cover holes in wall how to#
2. Best way to cover holes in wall Patch#
3. Best way to cover holes in wall professional#

Apply a thin coat of joint compund so that it completely covers the repair area and about 2 inches beyond it. Don’t put excess joint compound back into the tub, there may be dust or debris in it.ħ. When you apply joint compound you will use the larger scraper (6”), using the smaller scraper (4”) to hold excess. Now its time for the joint compound, two scrapers and drywall tape.

Apply construction adhesive to the paint stirrers that you put in place yesterday.

Best way to cover holes in wall Patch#

It’s better to need to cut a little bit more off than to have a patch that is just too small.Ħ. The patch doesn’t have to be an exact fit but it should be fairly close. Now cut a patch that is the same size as the hole you have made. You should have let the paint stirrers set overnight so that the adhesive is dry. These need to dry overnight to ensure that the adhesive is set.ĥ. Put the paint stirrers through the hole and pull them towards you firmly. Then put a generous amount of construction adhesive on the ends. Check that you will be able to put them through to the backside of the area that you are fixing, either horizontally or vertically. Next you will cut the paint stirrers until they are about three inches wider than the area you are trying to repair. This is what you want to try to accomplish.)ĥ. (Note the clean, angled edges of the repair on the right side. If you can angle the edges a little, this is best, but as long as you don’t have any rough edges you are ready to proceed. Now that you have cut out the damaged area and have all of your supplies, use the utility knife to clean up the edges of your repair area. A standard, all-purpose joint compound will work best and give you the smoothest final product.Ĥ. There are lots of different types of joint compound. Stores will usually sell 2 x 2 pieces of drywall to use for patching.Ī note on materials before you continue. Most homes use 1/2” thickness drywall, but if you aren’t sure it’s ok to ask. Someone there will be able to help you find a piece of drywall that is the same thickness of the damaged drywall. At this point, if you don’t already have your supplies, take the section you just cut out with you to the hardware store. A sharp blade is going to cut more cleanly and be safer to use.ģ. It may be easier to make several cuts along one line instead of trying to go all the way through on the first pass. Using a utility knife with a sharp blade, cut along the lines that you just made until it goes all the way through the drywall. Measure about 1” from the edge of the hole.Ģ. Measure and mark the area of drywall that you are going to remove. You will need to work on this over a few days to allow for drying time. Now here’s the step-by-step process to help you complete your repair. This size should be ample for these types of repairs. ** Drywall compound (or “mud” as it’s called in the trade) is premixed and available in 1-gallon pails. The store staff will also be able to see how large of a hole you need to repair and help you purchase the right quantity of drywall. * Drywall comes in different thicknesses so you will need to complete the first few steps before you cut out the damaged drywall piece to bring to the hardware store. Someone there will be able to help you find a piece of drywall that is the same thickness of the damaged drywall.

4” and 6” taping knives, or flexible scrapers.A utility knife (with a new, sharp blade).Ruler or something to use as a straight edge.A few paint stirrers (free at most hardware stores), the number will depend on the size of the hole you are fixing.

Best way to cover holes in wall professional#

No professional tools are required. For example, a professional would use a screw gun and not use glue at all. It just requires travel to the hardware store and some patience. Materials and Tools Requiredįortunately, a hole can easily be repaired by a regular homeowner who doesn’t want to spend the time or expense to bring in a contractor. You are not being paid by the hour! As a rule, we add 3 coats of drywall (“mud”) but you could add 4 coats which is even better. You WILL have an expert level of finish if you apply thin coats, and take your time. You will need to allow for drying time in between several of the steps, so this is a repair that you will work on for a little while over a few days.

This project is rated “beginner.” We’ve broken down the steps in more detail than many guides so it’s easier for beginners to follow A Few Expectations

Best way to cover holes in wall how to#

See our page on how to fix cracks in walls.) If you’re tired of that hole in the wall, let’s fix it. Note: If your wall has more of a hairline crack, this is a different issue.